IIARD International Institute of Academic Research and Development

International Journal of Agriculture and Earth Science (IJAES )

E- ISSN 2489-0081
P- ISSN 2695-1894
VOL. 11 NO. 5 2025
DOI: 10.56201/ijaes.vol.11.no5.2025.pg61.77

---

Comparative Evaluation of Throughput Capacities and Whole Kernel Recovery for Cracking Operation of Dura, Tenera and Mixed Varieties of Palm Nut

Sam, E O, Ndirika, V I O, Usoh, G A and, Umoh E O

---

Abstract

This research focused on evaluating the comparison in throughput capacity and whole kernel recovery during cracking operation of Dura, Tenera and Mixed Varieties of Palm Nut. One thousand three hundred and fifty (1350) samples of 1000g each of fresh palm nuts were used for the experiment, 450 samples were dura, 450 samples tenera and 450 samples were mixed varieties. 150 samples were selected for each experimental run. Three (3) sets of runs were carried out for each variety at the same condition. The samples after drying to specified levels of moisture content, were cracked at 5 different speeds with 5 levels of feed rate. Mean values for each variety was computed and used for statistical analysis. Comparative analysis shows that mixed variety have significant variation of the percentage whole kernel recovery of 48.04 to 97.06%, while tenera variety have significant variation of the throughput capacity of 99.23 to 476.19kg/h. For dura variety, the highest whole kernel recovery of 90.35% was obtained at the cracking speed of 1600rpm, moisture content of 18.1% w.b and feed rate of 360kg/h, all at 0.05 level of significance. Analysis of variance (ANOVA) and result of the pairwise comparisons for variables in the three varieties of palm nut revealed that the effects of cracking speed, moisture content and feed rate on the performance parameters are statistically significant at 0.05 level of significance.

keywords:

Comparative Evaluation; Throughput Capacities; Whole Kernel Recovery; Cracking

---

References:

Antia, O., Aniekan, O., William, O. and Emmanuel, A. (2012). Power Requirement for Effective
Cracking of Dried Palm Nut. International Journal of Emerging Trends in Engineering
and Development. 7, 32-44.
Edet, J. A., Sam, E. O., and Ahaneku, I. E., and Igbozulike, A. O. (2022). Review of Relevant
Evapotranspiration Models for Estimating Reference Evapotranspiration. Umudike
Journals of Engineering and Technology (UJET); Vol. 8, No.1, pp. 88 – 97
Gbadam, E. K., Anthony, S.,and Asiam, E. K. (2009). The Determination of Some Design
Parameters for Palm Nut Crackers. European Journal of Scientific Research. 38(2): 315-
Ismail, S. O., Ojolo, S. J., Orisaleye, J. I., Adediran, A. A., and Fajuyitan, O. O. (2015). Design
and Development of an Improved Palm Kernel Shelling and Sorting Machine. European
International Journal of Science and Technology. 4(2): February, 2015
Muthurajah, R. N. (2002). Palm Oil Factory Hand Book. Palm Oil resource Institute New Delhi.
Pp. 35-56
Ndukwu, M .C. and Asoegwu, S. N. (2010). Functional Performance of a Vertical-Shaft
Centrifugal Palm Nut Cracker: Research in Agricultural Engineering, 56 (2): 77-83.
Obiakor, S. I. and Babatunde, O. O. (1999). Development and Testing of the NCAM Centrifugal
Palm Nut Cracker. AGRIMECH Research and Introduction Bulletin of the National Centre
for Agricultural Mechanization (NCAM). January, 1999
Okokon, F. B., Udoh, M., Antia, O. and Ette, I. (2007). Investigation into the Grading of Large
Scale Palm Nuts for Cracking. World Journal of Biotechnology, 8(2):1376-1384.
Okoli, J. U. (2003). Optimum Drying Time for Palm Nuts for Efficient Nut Cracking in Small-
Scale Oil Palm Processing Mills. Global Journal of Engineering Research, 2: 7-10.
Oyejobi, D. O., Abdulkadir, T. S.,Yusuf, I. T. and Badiru, M. T., (2012). Effects of Palm Kernel
Shells Sizes and Mix Ratios on Lightweight Concrete. USEP: Journal of Research
Information in Civil Engineering, 9(2):217-221.
Sam, E. O., Ndirika, V. I. O., Edet, J. A. and Udom, I. J. (2022a). Mathematical Model for
Predicting Whole Kernel Recovery of a Palm Nut Cracking Machine using Mixed Variety
of Palm Nut. Proceeding of 2022 Conference of Agricultural and Bioresource Engineering.
UNN. Pp 458 – 469
Sam, E. O., Ndirika, V. I. O. and Etoamaihe, U. J. (2022b). Model Development and Optimization
for Predicting Whole Kernel Recovery of Palm Nut Cracking Machine using Mixed
Varieties of Palm Nut. Umudike Journals of Engineering and Technology (UJET); Vol. 8,
No.1, pp. 37 – 48.
Sam E. O., Ndirika V. I. O., Umoh A. T., Usoh G. A., and Umoh E. O. (2024a) Determination of
the Optimum Moisture Content for the Whole Kernel Recovery during the Cracking
Process of Oil Palm Nuts. Advanced Journal of Science, Technology and Engineering.
ISSN: 2997-5972 Volume 4, Issue 4, 2024 (pp. 125-138)
Sam, E. O., Akpan, U. N., Edet, J. A. and Igbozulike, A. O. (2024b). Extraction and Determination
of Physiochemical Properties of Oil from Cotton Seed. International Journal of
Engineering and Modern Technology (IJEMT) E-ISSN 2504-8848 P-ISSN 2695-2149 Vol
No. 10 2024.
Sanni, L. A. and Adegbenjo, A. O. (2002). Properties of Palm Nuts and Fibre Residue that
Influence Mechanical Separation after Palm Oil Extraction. Proceedings of the Regional
Workshop on Promotion of Appropriate Agro-Processing Technologies in West Africa,
Ile-Ife, Nigeria, Post-Harvest Technology Research Group, pp. 186-196.
Shahbazi, F. (2012). Effects of Moisture Content, Impact Direction and Impact Energy on the
Cracking Characteristics of Apricot Pit. World Applied Sciences Journal 20(11): 1520-
Stephen, A. I. and Lukman, A. A. (2015). Design and Construction of Palm Kernel Cracker and
Separator. International Journal of Engineering Trends and Technology (IJETT). 20(3)
Feb 2015.
Udo, S. B., Adejuyigbe S. B., Ismaila S. O. and Adisa A. F. (2015). Performance Evaluation of a
Palm Kernel Nuts Cracking Machine. Journal of Natural Science, Engineering and
technology, 14(1): 111-116.
Umoh, E. O., Iwe, M. O., Ojimelukwe, P. C. and Sam, E. O. (2024). Modeling and Optimization
of Extrusion Process Variables for the Functional Properties of Extrudates from Aerial
Yam and Soybean Flour Blends using Response Surface Methodology. Research Journal
of Food Science and Quality Control (RJFSQC) E-ISSN 2756-5483 P-ISSN 2695-2459
Vol. 10. No. 4 2024
Usoh, G. A., Umoh, E. O., Orji, F. N., Ahuchaogu, I. I., Sam, E. O. and Edet, J. A. (2023).
Determination of Water Poverty Index in Mkpat Enin Metropolis of Akwa Ibom State
using Composite Index and Simple time Analysis Approaches. Adeleke University
Journals of Engineering and Technology 6 (2), 172-182, 2023.

DOWNLOAD PDF

---

Back